Perfection
2-part polyurethane is the ultimate performing, high gloss topside
finish. It provides the longest-lasting, ultra-high gloss finish that
has superb colour-retention, together with excellent chemical and
abrasion resistance. It has been formulated specifically to enable
skilled amateur users to achieve professional-quality results with
ease. UV filters combined with the chemical cure of the polyurethane to
give the longest life possible.
* Hardest, abrasion-resistant finish
making it an excellent choice for use on high wear areas e.g. decks
(with Intergrip additive).
* Chemically resistant to diesel, petrol, oil, mild acids and alkalis |
|
| Colour |
YHA183-Platinum,
YHA184-Med. White, YHA192-Off White, YHA194-Oyster White,
YHA198-Mat'horn White, YHA216-Royal Blue, YHB000-Snow White,
YHB663-Jade Mist Green, YHE294-Chilli Red, YHF991-Mauritius Blue,
YHK990-Flag Blue, YHS056-Fight. Lady Yellow, YHS070-Cream,
YHS299-Rochelle Red, YHS936-Lauderdale Blue, YHY999-Jet Black |
| Finish |
High Gloss |
| Specific Gravity |
1.167 |
| Volume Solids |
49.0% |
| Mix Ratio |
2:1 by volume (as supplied) , Converter/Curing Agent - YGB001 |
| Typical Shelf Life |
2 yrs |
| VOC (As Supplied) |
486 g/lt |
| Unit Size |
750 ml 2.5 Lt (some colours only) |
|
|
|
Drying |
|
5°C |
15°C |
23°C |
35°C |
|
|
| Touch Dry [ISO] |
11hrs |
7hrs |
4hrs |
3hrs |
| Pot Life |
5hrs |
3hrs |
2hrs |
1hrs |
|
|
Overcoating |
|
Substrate Temperature |
| |
5°C |
15°C |
23°C |
35°C |
| Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Perfection |
28hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
| Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-320 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the substrate.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE WOOD: Prime with UCP or Interprotect.
STEEL: Prime with Interprotect.
ALUMINIUM: Pre-prime using Etch Primer. Prime with Interprotect.
GRP:
Wash down with Yacht Line Super Cleaner, rinse with fresh water and
allow to dry. Sweep blast or abrade with 180-220 grade paper. No
priming necessary.
AGED/WEATHERED GELCOATS: Due to the
potentially porous nature of aged/weathered gelcoats the risk of
solvent/moisture entrapment after painting is much higher than when
gelcoat is new. As a result this entrapment could lead to blistering of
the paint film. To reduce the risk of paint film blistering it is
recommended that 3 coats of Interprotect are applied to seal the
gelcoat. Interprotect must be overcoated with Perfection Undercoat
prior to topcoat application.
ALL SUBSTRATES: Use Perfection Undercoat. |
|
|
| Method |
Sand the undercoat smooth with 320-400 grade (grit) wet or dry paper. Remove dust with a tack rag. Apply 2-3 coats. |
|
|
| Hints |
Mixing Stir
contents of each part prior to mixing. Add Curing Agent to the Base,
stir and leave for 20 minutes to allow bubbles to disperse.
Thinner International Retarder Thinner #9.
Cleaner International Retarder Thinner #9.
Ventilation and Humidity Control Apply in dry, well ventilated conditions. Avoid excessively humid conditions, over 80% relative humidity.
Other Best
applied at 15°C. For lighter colors, mix the first coat of finish 50:50
with the undercoat to improve the depth of color and opacity. Both
products should be mixed with respective curing agents first. For best
results when applying by roller, smooth off with a pad or brush. If
using as a deck paint, mix in non-slip additive. Full hardness is
achieved after 7-10 days at 15°C/59°F. If required, Perfection Matting
Additive (YZM914) is available for use with Perfection. See Perfection
Matting Additive datasheet for details on use. |
|
|
| Some Important Points |
Do
not use unless mixed thoroughly with the curing agent at specified
ratio. Avoid painting in direct sunlight. Avoid applying late in the
evening as condensation can cause a loss of gloss during overnight
cure. Allow to dry in a well ventilated environment. Product
temperature should be minimum 15°C/59°F and maximum 35°C/95°F. Ambient
temperature should be minimum 5°C/40°F and maximum 30°C/86°F. Substrate
temperature should be minimum 5°C/40°F and maximum 30°C/86°F. |
|
|
| Compatibility/Substrates |
Do
not use Perfection on flexible constructions. Will crack on carvel and
clinker/lapstrake hulls. Perfection should not be used over any
one-pack products. Not suitable for permanently immersed surfaces. |
|
|
| Number of Coats |
2-3 |
|
|
| Coverage |
(Theoretical) - 12.00 (m²/lt) |
|
|
| Recommended DFT |
37 microns dry
|
| Recommended WFT |
75 microns wet |
|
|
| Application Methods |
Brush, Roller , DO NOT SPRAY |
|
| Storage |
GENERAL INFORMATION:
Exposure
to air and extremes of temperature should be avoided. For the full
shelf life of this product to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection should be kept in securely closed containers during transport and storage.
|
|
|
| Safety |
GENERAL:
Contains isocyanates which may be harmful to the respiratory tract.
Read the label safety section for Health and Safety Information, also
available from our Technical Help Line.
DISPOSAL: Do not discard
tins or pour paint into water courses, use the facilities provided. It
is best to allow paints to harden before disposal.
Remainders of
Perfection cannot be disposed of through the municipal waste route or
dumped without permit. Disposal of remainders must be arranged for in
consultation with the authorities.
|
|
| IMPORTANT NOTES |
The
information given in this sheet is not intended to be exhaustive. Any
person using the product without first making further written enquiries
as to the suitability of the product for the intended purpose does so
at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
  , International, the Akzo Nobel logo and other products mentioned in this publication are trademarks of, or licensed to Akzo Nobel. |
|
Head Office
International Paint Ltd
P O Box 20980
Oriel House
16 Connaught Place
London W2 2ZB
United Kingdom
tel: +44 (0) 171 479 6000
fax: +44 (0) 171 479 6500 |
European Region
International Paint Ltd
Stoneygate Lane
Felling, Gateshead
Tyne & Wear NE10 0JY
United Kingdom
tel: +44 (0) 191 469 6111
fax: +44 (0) 191 438 3977 |
Asia Region
International Paint Singapore (Pte) Ltd
449 Tagore Industrial Avenue
01-03 Greatland Industrial Building
Singapore 787820
tel: +65 6453 1981
fax: +65 6453 1778 |
Australasia Region
International Paint
Unit E54, 76 Waterway Drive
Coomera Qld 4209
Australia
tel: +61 (0) 7 5573 9600
fax: +61 (0) 7 5573 9677 |
North America Region
International Paint LLC
2270 Morris Avenue
Union
New Jersey 07083
USA
tel: +1 (0) 908 686 1300
fax: +1 (0) 908 686 8545 |
South America Region
International Paint
Rod Rap tavares, KM 18.5
Predio Administrativo 11
Butanta CEP 05577-300
Sao Paulo, Brazil
tel: +55 (0) 11 3789 2000
fax: +55 (0) 11 3789 2200 |
|
