Perfection Varnish for Teak
	Varnishes
	High Performance Polyurethane Yacht Varnish

PRODUCT DESCRIPTION The ultimate in varnish performance, specially formulated for oily wood types, combining excellent chemical and abrasion resistance with superb gloss. * Chemical cure gives resistance to fuels, oil and mild acids and alkalis * Up to four times longer service life than ordinary varnishes PRODUCT INFORMATION Colour YVA856-Clear Finish Full gloss Specific Gravity 1.06 Volume Solids 54%  Mix Ratio 5:2 by volume (as supplied) , Converter/Curing Agent - YVA851 Typical Shelf Life 2 yrs VOC (As Supplied) 422 g/lt Unit Size 750 ml DRYING/OVERCOATING INFORMATION Drying 5ºC 15ºC 23ºC 35ºC Touch Dry [ISO] 7hrs 5hrs 2hrs 1hrs Pot Life 5hrs 3hrs 2hrs 1hrs Overcoating Substrate Temperature 5ºC 15ºC 23ºC 35ºC Overcoated By Min Max Min Max Min Max Min Max Perfection Varnish &nbsp24hrs &nbsp4days &nbsp14hrs &nbsp3days &nbsp6hrs &nbsp2days &nbsp4hrs &nbsp1days Perfection Varnish for Teak &nbsp24hrs &nbsp4days &nbsp14hrs &nbsp3days &nbsp6hrs &nbsp2days &nbsp4hrs &nbsp1days Schooner &nbsp36hrs &nbsp1mths &nbsp16hrs &nbsp1mths &nbsp12hrs &nbsp1mths &nbsp8hrs &nbsp1mths Schooner (YVA084) &nbsp36hrs &nbsp1mths &nbsp16hrs &nbsp1mths &nbsp12hrs &nbsp1mths &nbsp8hrs &nbsp1mths Note:If maximum overcoating times are exceeded, sand using 280-320 grade (grit) wet or dry paper. Perfection Varnish for Teak must be sanded with 320-400 grade paper (and dust removed) prior to overcoating with Schooner. APPLICATION AND USE Preparation PREVIOUSLY VARNISHED WOOD: In Good Condition: Clean with Yacht Line Super Cleaner. Sand smooth with 280-320 grade paper. Remove sanding dust with thinners. In Poor Condition: Remove all previous coatings. BARE WOOD: Sand smooth with 80-180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying the first coat. Priming bare wood:: Thin the first coat by 20%. Method For best results when applying by roller, smooth off with a pad or brush. Performance will be further enhanced if top coated with 2 coats of Perfection Varnish. If using as a primer on flexible constructions, apply one coat only under Original. Avoid using direct from the can. Hints Mixing Stir individual products prior to mixing. Add Curing Agent to the Base, stir and leave for 10 minutes to allow bubbles to disperse. Mix the amount you expect to use in a separate container. Thinner YTA006 Thinners No.9 Cleaner YTA006 Thinners No.9 Ventilation and Humidity Control Apply 4 coats minimum in dry, well ventilated conditions. Best applied at ambient temperatures of between 15°C and 20°C. Sensitive to moisture during application. Avoid excessively humid conditions, over 80% relative humidity. Avoid applying late in the evening as condensation can cause a loss of gloss overnight. Some Important Points Avoid painting in direct sunlight. Avoid humid conditions. DO NOT SPRAY. Contains Isocyanates which may be harmful to lungs, read the safety data section before use. Do not use unless mixed thoroughly with the curing agent at specified ratio. Do not use on light-coloured wood as it will darken on exposure. Not suitable for continuous immersion. Product temperature should be minimum 15°C and maximum 35°C. Substrate temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Compatibility/Substrates Use only on oily timbers such as Teak. Do not use Perfection Varnish for Teak on flexible constructions. It should not be used over any one pack products. Number of Coats 4 coats minimum Coverage (Theoretical) - 18.18 (m²/lt) (Practical) - 16.00 (m²/lt) Recommended DFT 30 microns dry by brush Recommended WFT 55 microns wet by brush Application Methods Brush, Roller TRANSPORTATION,STORAGE AND SAFETY INFORMATION Storage GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Perfection Varnish for Teak to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight. TRANSPORTATION: Perfection Varnish for Teak should be kept in securely closed containers during transport and storage. Safety GENERAL: Read the label safety section for Health and Safety Information, also available from our Technical Help Line. DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal. Remainders of Perfection Varnish for Teak cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities. IMPORTANT NOTES The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability of the product for the intended purpose does so at their own risk and we can accept no responsibility for the performance of the product or for any loss or damage (other than death or personal or injury resulting from negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development. and International are registered trademarks of Akzo Nobel. Regional Addresses Head Office International Paint Ltd P O Box 20980 Oriel House 16 Connaught Place London W2 2ZB United Kingdom tel: +44 (0) 171 479 6000 fax: +44 (0) 171 479 6500 European Region International Paint Ltd Stoneygate Lane Felling, Gateshead Tyne & Wear NE10 0JY United Kingdom tel: +44 (0) 191 469 6111 fax: +44 (0) 191 438 3977 Asia Region International Paint Singapore (Pte) Ltd 449 Tagore Industrial Avenue 01-03 Hong Joo Industrial Building Singapore 787820 tel: +65 6453 1981 fax: +65 6453 1778 Australasia Region International Paint 115 Hyde Road Yeronga, Brisbane Queensland 4104 Australia tel: +61 (0) 7 3892 8866 fax: +61 (0) 7 3892 4287 North America Region International Paint Inc 2270 Morris Avenue Union New Jersey 07083 USA tel: +1 (0) 908 686 1300 fax: +1 (0) 908 686 8545 South America Region International Paint Rod Rap tavares, KM 18.5 Predio Administrativo 11 Butanta CEP 05577-300 Sao Paulo, Brazil tel: +55 (0) 11 3789 2000 fax: +55 (0) 11 3789 2200

			Ref: Issue Date: Supersedes:	05000016 22-Sep-2003 28-Nov-2002