Use
Pre-Kote as an undercoat for Toplac or Interlux Super yacht enamels.
Excellent obliteration allows for easy colour changing.
* Range of colours to compliment topcoat
* Easy application and rub down
* Long overcoating times to allow coat-on-coat application
The tough, flexible resins are long lasting, easy to apply and rub
down, giving a smooth base for the finishing coat. Suitable for all
primed wood, steel, alloy or GRP. |
|
| Colour |
YUB000-White, YUB783-Red, YUG879-Blue Grey, YUK954-Dark Blue |
| Finish |
Low sheen |
| Specific Gravity |
1.500 |
| Volume Solids |
47% |
| Typical Shelf Life |
2 yrs |
| VOC (As Supplied) |
363 g/lt |
| Unit Size |
750 ml 375 ml (some colours only) 2.5 Lt (some colours only) |
|
|
|
Drying |
|
5°C |
15°C |
23°C |
35°C |
|
|
| Touch Dry [ISO] |
15hrs |
6hrs |
3hrs |
1hrs |
| Sandable |
48hrs |
30hrs |
24hrs |
24hrs |
|
|
Overcoating |
|
Substrate Temperature |
| |
5°C |
15°C |
23°C |
35°C |
| Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Brightside |
 36hrs |
 4days |
 24hrs |
 3days |
 16hrs |
 2days |
 4hrs |
 1days |
| Interdeck |
 36hrs |
 4days |
 24hrs |
 3days |
 16hrs |
 2days |
 4hrs |
 1days |
| Interlux Super |
 36hrs |
 4days |
 24hrs |
 3days |
 16hrs |
 2days |
 4hrs |
 1days |
| Pre-Kote |
 36hrs |
 4days |
 24hrs |
 3days |
 16hrs |
 2days |
 4hrs |
 1days |
| Toplac |
 36hrs |
 4days |
 24hrs |
 3days |
 16hrs |
 2days |
 4hrs |
 1days |
|
| Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180-220 grade paper.
In Poor Condition: Remove all previous coatings and prime the substrate.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE WOOD: Prime with Yacht Primer or UCP.
STEEL: Prime with Yacht Primer or Interprotect.
ALUMINIUM: Prime with Etch Primer followed by either Yacht Primer or Interprotect.
GELCOAT/COMPOSITE:
No priming necessary. Wash down with Super Cleaner, rinse with fresh
water and allow to dry. Abrade with 180-220 grade paper.
ALL SUBSTRATES: If any filling is required use the appropriate product from the Interfill range. |
|
|
| Method |
Apply
1-2 coats. If maximum overcoating time of previous coating/primer is
exceeded, abrade using 220-320 grade wet or dry paper. Remove dust with
a dust wipe. To give extra depth of colour, Toplac or Interlux Super
enamels may be added to the undercoat. |
|
|
| Hints |
Mixing Stir well before use.
Thinner YTA800,YTA063 Thinner No.1 (Thinner No.10 for spraying)
Cleaner YTA800 Thinners No.1
Ventilation and Humidity Control Apply in dry, well ventilated conditions.
Airless Spray Pressure: 180 bar. Tip Size: 1365-1580.
Conventional Spray For
conventional spray application, reduce viscosity using Thinners No. 10
to 20 - 24 seconds, BS4. Pressure: 3-4 bar. Tip Size: 1.4-1.8 mm. |
|
|
| Some Important Points |
Substrate
temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Product
temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Ambient
temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Do not
use below 5°C. |
|
|
| Compatibility/Substrates |
Can
be applied over all Interfill products. Only overcoat with one-pack
paints. Not suitable for permanently immersed surfaces. |
|
|
| Number of Coats |
1-2 |
|
|
| Coverage |
(Theoretical) - 13.33 (m²/lt) |
|
(Practical) - 12.00 (m²/lt) by brush, 8 m²/lt by spray |
|
|
| Recommended DFT |
35 microns dry by brush
|
| Recommended WFT |
75 microns wet by brush |
|
|
| Application Methods |
Brush, Roller, Airless Spray, Conventional Spray |
|
| Storage |
GENERAL INFORMATION:
Exposure
to air and extremes of temperature should be avoided. For the full
shelf life of Pre-Kote to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Pre-Kote should be kept in securely closed containers during transport and storage.
|
|
|
| Safety |
GENERAL: Read the label safety section for Health and Safety Information, also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Pre-Kote cannot be disposed of through the
municipal waste route or dumped without permit. Disposal of remainders
must be arranged for in consultation with the authorities.
|
|
| IMPORTANT NOTES |
The
information given in this sheet is not intended to be exhaustive. Any
person using the product without first making further written enquiries
as to the suitability of the product for the intended purpose does so
at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
  , International, the Akzo Nobel logo and other products mentioned in this publication are trademarks of, or licensed to Akzo Nobel. |
|
Head Office
International Paint Ltd
P O Box 20980
Oriel House
16 Connaught Place
London W2 2ZB
United Kingdom
tel: +44 (0) 171 479 6000
fax: +44 (0) 171 479 6500 |
European Region
International Paint Ltd
Stoneygate Lane
Felling, Gateshead
Tyne & Wear NE10 0JY
United Kingdom
tel: +44 (0) 191 469 6111
fax: +44 (0) 191 438 3977 |
Asia Region
International Paint Singapore (Pte) Ltd
449 Tagore Industrial Avenue
01-03 Hong Joo Industrial
Building
Singapore 787820
tel: +65 6453 1981
fax: +65 6453 1778 |
Australasia Region
International Paint
115 Hyde Road
Yeronga, Brisbane
Queensland 4104
Australia
tel: +61 (0) 7 3892 8866
fax: +61 (0) 7 3892 4287 |
North America Region
International Paint LLC
2270 Morris Avenue
Union
New Jersey 07083
USA
tel: +1 (0) 908 686 1300
fax: +1 (0) 908 686 8545 |
South America Region
International Paint
Rod Rap tavares, KM 18.5
Predio Administrativo 11
Butanta CEP 05577-300
Sao Paulo, Brazil
tel: +55 (0) 11 3789 2000
fax: +55 (0) 11 3789 2200 |
|
