|
|
Toplac
is a premium gloss marine enamel for all
substrates above the waterline. It is exceptionally easy to apply by brush
or roller and pad and contains UV filter for increased durability.
* Excellent flow characteristics
* Range of bright colours
* Over twice the life of ordinary alkyd enamels
Its unique chemical structure enables Toplac to
outperform traditional finishes giving a long lasting high definition
gloss.
|
|
|
Colour
|
YKA184-Med. White,
YKA187-Ivory, YKA905,YKB000-Snow White,
YKB914-Baltic Blue, YKB993-Oxford Blue, YKE938-Danube Blue, YKF684-Atlantic
Grey, YKF991-Mauritius Blue, YKJ292-Bounty, YKS101-Yellow, YKS299-Rochelle
Red, YKS936-Lauderdale Blue, YKT541-Donegal Green, YKU898-Bondi Blue,
YKY999-Jet Black, YKZ501-Rustic Red . Refer to colour
chart for further details.
|
|
Finish
|
High Gloss
|
|
Specific Gravity
|
1.1
|
|
Volume Solids
|
51%
|
|
Typical Shelf Life
|
2 yrs
|
|
VOC (As Supplied)
|
404 g/lt
|
|
VOC (EU Solvent)
|
367.3 g/kg EU
Solvent Emissions Directive (Council Directive 1999/13/EC)
|
|
Unit Size
|
750 ml 375 ml (some colours only) 2.5 Lt (some colours
only)
|
|
|
|
|
|
Drying
|
|
|
5°C
|
15°C
|
23°C
|
35°C
|
|
|
|
|
|
|
|
|
|
|
|
|
Touch Dry [ISO]
|
6hrs
|
3hrs
|
2hrs
|
1hrs
|
|
|
|
|
|
|
Overcoating
|
|
Substrate
Temperature
|
|
5°C
|
15°C
|
23°C
|
35°C
|
|
|
Overcoated By
|
Min
|
Max
|
Min
|
Max
|
Min
|
Max
|
Min
|
Max
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Toplac
|
24hrs
|
4days
|
16hrs
|
3days
|
8hrs
|
2days
|
6hrs
|
1days
|
|
|
|
|
|
|
|
|
|
|
Preparation
|
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Super Cleaner, rinse
with fresh water and allow to dry. Abrade with 280-320 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the
substrate.
PRIMING: Substrate preparation is covered separately on the primer
datasheet.
BARE WOOD: Prime with Yacht Primer or UCP.
STEEL: Prime with Yacht Primer or Interprotect.
ALUMINIUM: Prime with Etch Primer followed by either Yacht Primer or
Interprotect.
GRP: Wash down with Super Cleaner, rinse
with fresh water and allow to dry. Abrade with 180-220 grade paper.
AGED/WEATHERED GELCOATS: Due to the potentially porous nature of
aged/weathered gelcoats the risk of
solvent/moisture entrapment after painting is much higher than when gelcoat is new. As a result this entrapment could lead
to blistering of the paint film. To reduce the risk of paint film
blistering it is recommended that 3 coats of Interprotect
are applied to seal the gelcoat. Interprotect must be overcoated
with Polyurethane Basecoat prior to topcoat application.
ALL SUBSTRATES: Use Pre-Kote undercoat. If
spray applying Toplac, Pre-Kote
must be aged a minimum of 14 days. If this is not possible Polyurethane
Basecoat can also be used as an undercoat.
|
|
|
|
Method
|
Sand the undercoat smooth with 320-400 grade
(grit) wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.
|
|
|
|
Hints
|
Mixing Stir well
before use.
Thinner Thinner No.1 Thinner No.10 - For Professional use ONLY.
Thinning In warm or windy conditions up to 10% of thinner may
be added to ease application.
Cleaner Thinner No.1
Ventilation and Humidity Control Apply in dry,
well ventilated conditions. Avoid applying late in the evening as
condensation can cause a loss of gloss overnight.
Conventional Spray Thin 10-25% with Thinner No.10 (For
Professional use ONLY) to a viscosity of 18-22 secs
(BS4) or 16-20 secs (DIN4). Pressure: 3-4 bar. Tip Size: 1.1-1.4 mm. NOTE: Pre-Kote
undercoat MUST be aged a minimum of 14 days before application of Toplac.
Other For lighter colours, mix the
first coat of finish 50:50 with the undercoat to improve the depth of colour and opacity. For best results when applying by
roller, smooth off with a pad or brush.
|
|
|
|
Some Important Points
|
Toplac may discolour if used at temperatures above 80°C. Not
suitable for permanently immersed surfaces. Do not use below 5°C. Ambient
temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Product
temperature should be minimum 15°C and maximum 35°C. Substrate temperature
should be minimum 5°C/40°F and maximum 35°C/95°F. Avoid applying late in
the evening as condensation can cause a loss of gloss during overnight
cure.
|
|
|
|
Compatibility/Substrates
|
Use over suitably prepared and undercoated
surfaces or existing paint schemes.
|
|
|
|
Number of Coats
|
1-2 by brush
|
|
|
|
Coverage
|
(Theoretical) - 13.33 (m²/lt)
|
|
(Practical) - 12.00 (m²/lt)
by brush, 8 m²/lt by spray
|
|
|
|
Recommended DFT
|
38 microns dry
|
|
Recommended WFT
|
75 microns wet
|
|
|
|
Application Methods
|
Brush, Conventional Spray, Roller
|
|
|
|
TRANSPORTATION,STORAGE AND SAFETY
INFORMATION
|
|
Storage
|
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the full
shelf life of Toplac to be realised
ensure that between use the container is firmly closed and the temperature
is between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Toplac should be kept in securely closed
containers during transport and storage.
|
|
|
|
Safety
|
GENERAL: Read the
label safety section for Health and Safety Information, also available from
our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before disposal.
Remainders of Toplac cannot be disposed of
through the municipal waste route or dumped without permit. Disposal of
remainders must be arranged for in consultation with the authorities.
|
|
|
|
|
|
IMPORTANT
NOTES
|
The information
given in this sheet is not intended to be exhaustive. Any person using the product
without first making further written enquiries as to the suitability of the
product for the intended purpose does so at their own risk and we can
accept no responsibility for the performance of the product or for any loss
or damage (other than death or personal or injury resulting from
negligence) arising out of such use. The information contained in this
sheet is liable to modification from time to time in the light of
experience and our policy of continuous product development.
|
|
  , International , the Akzo
Nobel logo and other products mentioned in this publication are trademarks
of, or licensed to Akzo Nobel.
|
|
|
|
Head Office
International Paint Ltd
P O Box 20980
Oriel House
16 Connaught Place
London W2 2ZB
United Kingdom
tel: +44 (0) 171 479 6000
fax: +44 (0) 171 479 6500
|
European Region
International Paint Ltd
Stoneygate Lane
Felling, Gateshead
Tyne & Wear NE10 0JY
United Kingdom
tel: +44 (0) 191 469 6111
fax: +44 (0) 191 438 3977
|
Asia Region
International Paint Singapore (Pte) Ltd
449 Tagore Industrial Avenue
01-03 Greatland Industrial Building
Singapore 787820
tel: +65 6453 1981
fax: +65 6453 1778
|
Australasia Region
International Paint
Unit E54, 76 Waterway Drive
Coomera Qld 4209
Australia
tel: +61 (0) 7 5573 9600
fax: +61 (0) 7 5573 9677
|
North America Region
International Paint LLC
2270 Morris Avenue
Union
New Jersey 07083
USA
tel: +1 (0) 908 686 1300
fax: +1 (0) 908 686 8545
|
South America Region
International Paint
Rod Rap tavares, KM 18.5
Predio Administrativo
11
Butanta CEP 05577-300
Sao Paulo, Brazil
tel: +55 (0) 11 3789 2000
fax: +55 (0) 11 3789 2200
|
|
