Offers
protection in low to medium fouling conditions where a hard, scrubbable
antifouling is required. Ideal for fast powerboats, propellers,
outdrives, sterngear and the waterline.
* Medium strength, hard
antifouling based on Biolux Technology - a unique system of organic
boosting biocides in a highly effective controlled-release film
* Hard, scrubbable finish to allow clean-off if needed
* Suitable for burnishing to provide a smooth finish
* Aluminium compatible formulation
* Range of bright colours |
|
| Colour |
YBA508-White, YBA515-Blue, YBA521-Green, YBA550-Scarlet, YBA563-Grey, YBA591-Black |
| Finish |
Matt |
| Specific Gravity |
1.4 |
| Volume Solids |
46% average |
| Typical Shelf Life |
2 yrs |
| VOC (As Supplied) |
472 g/lt |
| Unit Size |
375 ml 750 ml 2.5 Lt 5 Lt |
|
|
|
Drying |
|
5°C |
15°C |
23°C |
35°C |
|
|
| Touch Dry [ISO] |
1hrs |
45mins |
30mins |
20mins |
| Immersion |
24hrs |
12hrs |
8hrs |
6hrs |
|
|
Note:Max.
Immersion Times are as follows: 5-15°C - 3 mths; 23°C - 2 mths; 35°C -
1 mth If maximum immersion time is exceeded, high pressure water wash
or wet abrade with 180-240 grade paper prior to immersion. |
|
Overcoating |
|
Substrate Temperature |
| |
5°C |
15°C |
23°C |
35°C |
| Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Trilux |
16hrs |
ext |
10hrs |
ext |
6hrs |
ext |
4hrs |
ext |
|
| Preparation |
PREVIOUSLY ANTIFOULED SURFACE:
In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON: Prime with Interprotect or Primocon.
LEAD: Etch Primer followed by Interprotect or Primocon.
WOOD: Preserve, if required, with Intertox. Prime with Interprotect or Primocon.
ALUMINIUM/ALLOY: Interprotect, or Etch Primer followed by Primocon. |
|
|
| Method |
Apply 2-3 coats on the area to be coated per season. |
|
|
| Hints |
Mixing Stir well before use.
Thinner YTA085 Thinners No.3
Thinning Thinning is not recommended.
Cleaner YTA085 Thinners No.3
Airless Spray Pressure: 176-210 bar. Tip Size: 2180.
Other For
Airmix spray application: Pressure: 2.5 bar. Tip Size: 20-113. Take
care to apply all the paint calculated even if it means applying an
extra coat. It is important for performance to apply the correct
thickness. |
|
|
| Some Important Points |
To
prevent premature failure, ensure the correct amount of paint is
applied using the coverage as a guide. Product temperature should be
minimum -5°C and maximum 35°C. Ambient temperature should be minimum
-5°C and maximum 35°C. Substrate temperature should be minimum 1°C
above dew point and maximum 35°C. |
|
|
| Compatibility/Substrates |
Suitable
for use on all substrates including suitably primed Aluminium/Alloy and
Zinc-sprayed metals. Can be applied direct over most types of
antifoulings, provided they are in sound condition. |
|
|
| Number of Coats |
2-3 by brush/roller |
|
|
| Coverage |
(Theoretical) - 10.50 (m²/lt) by brush; 3.0 m²/lt spray. |
|
|
| Recommended DFT |
40 microns dry
|
| Recommended WFT |
85 microns wet |
|
|
| Application Methods |
Airless Spray, Brush, Airmix, Roller |
|
| Storage |
GENERAL INFORMATION:
Exposure
to air and extremes of temperature should be avoided. For the full
shelf life of Trilux to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Trilux should be kept in securely closed containers during transport and storage.
|
|
|
| Safety |
GENERAL:
Contains biocides. Antifoulings should only be wet sanded. Never dry
sand or burn-off old antifoulings. Read the label safety section for
Health and Safety Information, also available from our Technical Help
Line.
DISPOSAL: Do not discard tins or pour paint into water
courses, use the facilities provided. It is best to allow paints to
harden before disposal.
Remainders of Trilux cannot be disposed of
through the municipal waste route or dumped without permit. Disposal of
remainders must be arranged for in consultation with the authorities.
|
|
| IMPORTANT NOTES |
The
information given in this sheet is not intended to be exhaustive. Any
person using the product without first making further written enquiries
as to the suitability of the product for the intended purpose does so
at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
  , International, the Akzo Nobel logo and other products mentioned in this publication are trademarks of, or licensed to Akzo Nobel. |
|
Head Office
International Paint Ltd
P O Box 20980
Oriel House
16 Connaught Place
London W2 2ZB
United Kingdom
tel: +44 (0) 171 479 6000
fax: +44 (0) 171 479 6500 |
European Region
International Paint Ltd
Stoneygate Lane
Felling, Gateshead
Tyne & Wear NE10 0JY
United Kingdom
tel: +44 (0) 191 469 6111
fax: +44 (0) 191 438 3977 |
Asia Region
International Paint Singapore (Pte) Ltd
449 Tagore Industrial Avenue
01-03 Hong Joo Industrial
Building
Singapore 787820
tel: +65 6453 1981
fax: +65 6453 1778 |
Australasia Region
International Paint
115 Hyde Road
Yeronga, Brisbane
Queensland 4104
Australia
tel: +61 (0) 7 3892 8866
fax: +61 (0) 7 3892 4287 |
North America Region
International Paint LLC
2270 Morris Avenue
Union
New Jersey 07083
USA
tel: +1 (0) 908 686 1300
fax: +1 (0) 908 686 8545 |
South America Region
International Paint
Rod Rap tavares, KM 18.5
Predio Administrativo 11
Butanta CEP 05577-300
Sao Paulo, Brazil
tel: +55 (0) 11 3789 2000
fax: +55 (0) 11 3789 2200 |
|
